Heavy Equipment Forum 4 You

Caterpillar, Case, Komatsu, Kobelco, Htachi, John Deer, New Holland, Grove, NorthWest, Link-Belt, Manitowoc, Terex, Euclid, Marion, Bucyrus-Erie, International Harvester, Bob Cat, Lima, Bay City, Unit Rig, Dresser, Allis Chalmers, Fiat Allis, Oliver

Skip to content

Hard Facing

Welders, Cutting Torches, Jacks, Mills, Pressure Washers to name a few.
Post a reply

Hard Facing

Postby DarrylMueller » Sat May 30, 2009 12:42 pm

Lincoln Lincore 60 5/64 for hard facing, 212 5/64 for most other welding work, iner-shild wire is feed by LN-25. The Lincoln Commander 500 changes volts and amps automatic on the go wile welding powered by Duitz air cooled diesel. Pre-heat this will avoid spalding, taping with hammer helps to reduce cracking by stress relieving. Jamie did the welding. Bucket teeth, 4/1 bucket, 4 foot drill were hard faced in 6 hrs.
IMG_1611.JPG
IMG_1611.JPG (117.76 KiB) Viewed 132 times
IMG_1612.JPG
IMG_1612.JPG (133.97 KiB) Viewed 132 times
IMG_1613.JPG
IMG_1613.JPG (121 KiB) Viewed 132 times
IMG_1617.JPG
IMG_1617.JPG (120.7 KiB) Viewed 132 times
IMG_1618.JPG
IMG_1618.JPG (97.57 KiB) Viewed 132 times
IMG_1619.JPG
IMG_1619.JPG (105.7 KiB) Viewed 132 times
IMG_1620.JPG
IMG_1620.JPG (1.1 MiB) Viewed 132 times
IMG_1622.JPG
IMG_1622.JPG (114.68 KiB) Viewed 132 times
IMG_1624.JPG
IMG_1624.JPG (119.01 KiB) Viewed 132 times
IMG_1629.JPG
IMG_1629.JPG (109.56 KiB) Viewed 132 times
IMG_1625.JPG
IMG_1625.JPG (126.92 KiB) Viewed 132 times
IMG_1626.JPG
IMG_1626.JPG (74.61 KiB) Viewed 132 times
IMG_1627.JPG
IMG_1627.JPG (105.15 KiB) Viewed 132 times
IMG_1628.JPG
IMG_1628.JPG (84.33 KiB) Viewed 132 times
IMG_1630.JPG
IMG_1630.JPG (96.72 KiB) Viewed 133 times
IMG_1631.JPG
IMG_1631.JPG (92.84 KiB) Viewed 132 times
The attachment IMG_1631.JPG is no longer available
Attachments
IMG_1623.JPG
IMG_1623.JPG (97.66 KiB) Viewed 130 times
"When people fear the government this is TYRANNY. When the government fears the people this is LIBERTY. Thomas Jefferson"
"The problem with socialism is that you eventually run out of other people's money. Margaret Thatcher"
"Only difference between a communist & a socialist is a communist uses a gun to steal. They both use environmental laws to redistribute wealth. They are both like water melon, green on the outside environmentalism, red on the inside socialist-communist ideals."
Debit that comes from the Stimulus Bill. The debtor is a slave to the debit. We The People are now a slave to this debit.

Darryl
DarrylMueller
Site Admin
 
Posts: 217
Joined: Sat Dec 13, 2008 12:22 pm
Location: Altamont Pass, Livermore, CA
Top

Re: Hard Facing

Postby charlie@jifco.com » Fri Jun 05, 2009 10:36 am

Who's that welder? :mrgreen:
Charlie
charlie@jifco.com
 
Posts: 1
Joined: Fri Jun 05, 2009 10:30 am
Top

Re: Hard Facing

Postby DarrylMueller » Sun Jun 07, 2009 7:42 am

Hi Charlie Welcom to the forum. How about posting the robot and the big lathes.
"When people fear the government this is TYRANNY. When the government fears the people this is LIBERTY. Thomas Jefferson"
"The problem with socialism is that you eventually run out of other people's money. Margaret Thatcher"
"Only difference between a communist & a socialist is a communist uses a gun to steal. They both use environmental laws to redistribute wealth. They are both like water melon, green on the outside environmentalism, red on the inside socialist-communist ideals."
Debit that comes from the Stimulus Bill. The debtor is a slave to the debit. We The People are now a slave to this debit.

Darryl
DarrylMueller
Site Admin
 
Posts: 217
Joined: Sat Dec 13, 2008 12:22 pm
Location: Altamont Pass, Livermore, CA
Top
Post a reply

Return to Shop Equipment

Who is online

Users browsing this forum: No registered users and 1 guest

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
cron